Body Metrics Calc

Skinfold body fat calculator: caliper 3-site method

Pinch three sites with a caliper, add your age, and get body fat from the Jackson-Pollock 3-site equation.

Updated 2026-10-18

Sex
Units

Diagonal fold halfway between the armpit crease and the nipple

Vertical fold 2 cm to the right of the navel

Vertical fold on the back of the arm, halfway between shoulder and elbow

Diagonal fold just above the top of the hip bone

Vertical fold on the front of the thigh, halfway between hip crease and kneecap

Adults 18 to 80

Adds fat mass and lean mass to the result

Skinfold sites, front and backBody outline from the front and back with numbered sites on the right side of the body: 1 chest, 2 abdomen, 3 triceps, 4 suprailiac, 5 thigh.12345FrontBack
Right side of the body. Men: 1, 2, 5. Women: 3, 4, 5.

Your estimate

Enter your numbers. The estimate updates as you type.

Estimates, not medical advice.

A skinfold caliper measures a double layer of skin and the fat just under it. Pinch three sites, add the readings, and the Jackson-Pollock 3-site equation turns that sum and your age into body density. The Siri equation then turns density into body fat percentage.

Men use the chest, abdomen and thigh. Women use the triceps, suprailiac and thigh. If you add your weight, the calculator also splits it into fat mass and lean mass.

Where to pinch: the 3 sites

The numbers on the diagram match the inputs. Men pinch 1 chest, 2 abdomen and 5 thigh; women pinch 3 triceps, 4 suprailiac and 5 thigh. Stand relaxed and take every site on the right side of the body. Lift the fold just above the mark, put the caliper jaws on the mark and read the dial once the needle settles, still holding the fold.

Measure each site twice, going round all three sites before repeating, and average the two closest if they disagree. Skip it right after exercise or a hot shower.

The formula in plain words

Add the three skinfolds in millimetres. Call the total S.

Men: body density = 1.10938 − 0.0008267 × S + 0.0000016 × S² − 0.0002574 × age.

Women: body density = 1.0994921 − 0.0009929 × S + 0.0000023 × S² − 0.0001392 × age.

Then body fat % = 495 ÷ density − 450. That last step is the Siri equation from 1961, the same density conversion behind the original Navy tape equations.

The men's equation comes from Jackson and Pollock (1978), fitted on 308 men aged 18 to 61. The women's comes from Jackson, Pollock and Ward (1980), fitted on 249 women aged 18 to 55. Both were checked against underwater weighing. The calculator accepts ages 18 to 80, and flags any result above the study age range.

Worked example

A 30-year-old man pinches 15 mm at the chest, 25 mm at the abdomen and 20 mm at the thigh.

S = 15 + 25 + 20 = 60 mm.

Density = 1.10938 − 0.0008267 × 60 + 0.0000016 × 3,600 − 0.0002574 × 30 = 1.10938 − 0.04960 + 0.00576 − 0.00772 = 1.05782.

Body fat = 495 ÷ 1.05782 − 450 = 17.9%.

At 180 lb, that is 32.3 lb of fat mass and 147.7 lb of lean mass.

A 30-year-old woman with the same 60 mm sum (triceps, suprailiac and thigh) gets a density of 1.04402 and 24.1% body fat.

How accurate is a caliper

The equations predict group averages, so any one result can be off. Most of the error comes from the pinch, not the math: a fold taken 2 cm off the site, a caliper read too early or too late, or a fold that grabs muscle all change the reading. This calculator does not quote an error figure for that reason. A cheap plastic caliper and a clinic caliper can also read differently on the same fold.

For tracking change, consistency beats precision. Use the same caliper, the same sites, the same person pinching and the same time of day, and watch the trend in the skinfold sum as well as the percentage.

Skinfold, tape or BMI

The body fat calculator estimates body fat from a tape measure (US Navy method) or from your BMI, with no caliper needed. A tape is easier to use on your own, while a caliper measures fat at the sites directly. Running both and comparing them tells you more than either number alone. The Navy vs Army methods guide explains how the tape equations were built.

If you already know your body fat, the lean body mass calculator compares the result with three height and weight formulas.

Sources

  1. pubmed.ncbi.nlm.nih.gov: Jackson & Pollock 1978 (Br J Nutr 40:497), men
  2. pubmed.ncbi.nlm.nih.gov: Jackson, Pollock & Ward 1980 (Med Sci Sports Exerc 12:175), women
  3. pubmed.ncbi.nlm.nih.gov: Siri 1961, density to body fat (1993 reprint)

Questions people ask

Which skinfold sites does the 3-site method use?

Men use the chest, abdomen and thigh. Women use the triceps, suprailiac (just above the hip bone) and thigh. Take all of them on the right side of the body, standing relaxed.

How do I read a body fat caliper?

Pinch the fold just above the site, put the jaws on the site, and read the dial as soon as the needle settles while you keep holding the fold. Take each site at least twice and average the readings.

Can I measure my own skinfolds?

You can reach the abdomen and thigh, and with practice the chest or suprailiac. The triceps is hard to pinch on yourself. A partner gives more repeatable readings, and the same person each time is best for tracking change.

Why does my age change the result?

Both Jackson-Pollock equations include age. The same skinfold sum gives a higher body fat estimate at an older age, because in the study samples older people with the same sum had more body fat by underwater weighing.

Is a caliper more accurate than a tape measure?

Neither is accurate for one person in every case. Both are regression estimates checked against underwater weighing. A caliper depends heavily on technique, while a tape is easier to repeat on your own. Compare the two on the body fat calculator.