Body Metrics Calc

Swim pace calculator

Pace per 100 = time ÷ distance × 100. Enter any two of distance, time and pace to get the third, in metres or yards.

Updated 2026-10-09

Work out
Distance unit
Pace unit

Minutes and seconds (30:00) or hours too (1:05:30)

Minutes and seconds per 100, for example 2:00 or 1:45.5

Your estimate

Enter your numbers. The estimate updates as you type.

Estimates, not medical advice.

Swim pace is the time you take to cover 100 metres or 100 yards. Enter a distance and a time to get your pace in both units. Switch tabs to turn a pace into a finish time for any distance, or a pace and a time into the distance you will cover.

Time can be minutes and seconds (30:00) or hours, minutes and seconds (1:05:30). Pace is minutes and seconds per 100, and can carry tenths (1:45.5).

The formula in plain words

Pace: turn your time into seconds, divide by the distance in metres, then multiply by 100. That gives seconds per 100 m. Write it as minutes and seconds.

Finish time: multiply your pace in seconds per 100 m by the distance in metres, then divide by 100.

Distance: divide your time in seconds by your pace in seconds per 100 m, then multiply by 100 to get metres.

For yards, the only extra step is the unit. One yard is exactly 0.9144 m, so a pace per 100 yd is the pace per 100 m multiplied by 0.9144. Going the other way, divide by 0.9144. One mile is exactly 1,609.344 m. Both are definitions, listed in NIST Special Publication 811, so the conversion adds no error.

Worked example

You swim 1,500 m in 30:00.

30:00 is 1,800 seconds. Then 1,800 ÷ 1,500 × 100 = 120 seconds, which is 2:00 per 100 m.

Per 100 yd: 120 × 0.9144 = 109.7 seconds, which is 1:49.7 per 100 yd.

Going the other way: at 2:00 per 100 m, a 3.8 km swim is 38 × 120 = 4,560 seconds, or 1:16:00. And at 1:45 per 100 yd, 1,650 yd is 16.5 × 105 = 1,732.5 seconds, or 28:52.5.

Pace, per 100 yd and finish times

Pace per 100 mPace per 100 yd1,500 m3.8 km
1:301:22.322:3057:00
1:451:36.026:151:06:30
2:001:49.730:001:16:00
2:152:03.433:451:25:30
2:302:17.237:301:35:00

These rows are worked examples of the formula at an even pace, not averages for any group of swimmers. Your own test swim is the only number that gives your answer.

Yards or metres: check your pool

Pools are measured in yards or in metres, and the pace on your watch or the wall clock means a different distance in each. A 25 m length is about 27.34 yd. So 100 m is about 109.36 yd, and swimming 100 m at the same speed takes about 9.4% longer than 100 yd.

Before you compare paces, check which unit your pool uses and set the pace unit to match. The calculator always shows both, so a pace from a yards pool can be read against a target written per 100 m.

The conversion here is distance only. It does not adjust for starts, turns, wetsuits or open water, so a converted time is the same speed in the other unit, not a prediction of how you would race in a different pool.

The distance buttons cover common pool and race distances, from 50 m to 1,500 m, 1,650 yd and 1 mi. The 1.9 km and 3.8 km buttons are there for triathletes. Events set their own swim distances, so check your race information and type the exact figure if it differs.

How to time a test swim

  1. Warm up first, so the test reflects your steady pace rather than a cold start.
  2. Pick a distance you can hold at an even effort, such as 400 m or 1,500 m, and know the exact pool length.
  3. Push off from the wall and start the clock, or use the pace clock on the wall. Count every length.
  4. Stop the clock as you touch the wall at the end. Enter the distance and time above.

Counting lengths is where most errors come from. A missed length in a 25 m pool puts the pace off by 25 m worth of time, so use a lap counter or count in sets of four. Swim the test the same way each time, in the same pool, so results compare fairly.

For walking and running distance, see the steps to miles calculator.

Sources

  1. nist.gov: NIST SP 811, Guide for the Use of the SI (exact unit definitions)

Questions people ask

How do I calculate my swim pace per 100 m?

Turn your time into seconds, divide by the distance in metres and multiply by 100. A 1,500 m swim in 30:00 is 1,800 ÷ 1,500 × 100 = 120 seconds, or 2:00 per 100 m.

How do I convert a pace per 100 yd to per 100 m?

Divide the pace in seconds by 0.9144, because one yard is exactly 0.9144 m. A pace of 1:30 per 100 yd is 90 ÷ 0.9144 = 98.4 seconds, or 1:38.4 per 100 m. To go from metres to yards, multiply by 0.9144.

How long will a 1,500 m swim take at 2:00 per 100 m?

1,500 m is 15 lots of 100 m, so 15 × 2:00 = 30:00, if you hold that pace the whole way.

Is 1,650 yd the same as a mile?

No. A mile is 1,760 yd (1,609.344 m). 1,650 yd is 1,508.76 m, which is 110 yd (about 100.6 m) short of a mile.

Does the calculator allow for turns or open water?

No. It converts distance and time at an even pace. Starts, turns, wetsuits, currents and sighting all change real swim times, so use a test swim in the same conditions as your target.